Most fence post repair jobs come down to one question: is the timber above the ground still sound? If a wooden post has rotted or snapped at ground level but is solid higher up, a concrete repair spur bolted alongside it will usually hold it upright again. If the post is rotten or split above ground, or it is a concrete post that has cracked, the post needs replacing.
The trick is diagnosing the cause before buying anything. A spur fixes rot at the ground line. It does nothing for a split post, and it only helps a leaning post if the ground around it is stable.
Why timber posts fail at ground level
Wood-decay fungi need moisture, oxygen and something to feed on. At the ground line a post gets moisture from the soil and oxygen from the air, so that is where decay is fastest. It is also where the bending stress from a wind-loaded panel is highest, which is why rotten posts snap there.
Fence posts belong to Use Class 4 under BS 8417, the treatment level for wood in contact with the ground. Timber Development UK and the Wood Protection Association use a default service life of 15 years for this class unless 30 years is specified. A post treated to a lower class, or one that has been cut and had its cut end buried, will usually fail sooner.
Leaning posts are a different problem. Clay soils swell when wet and shrink when dry, and the British Geological Survey notes that the most susceptible clay formations are mainly in south-east Britain. A footing that is too shallow or too narrow has little grip on ground that moves with the seasons, so it can work loose over time.
Fence post repair options: spur, support or replacement
Start with a push test on each post, then dig a little soil away from the base so you can see the wood and the top of the concrete footing.
| What you see | Likely cause | Fix | When that fix fails |
|---|---|---|---|
| Timber post soft or snapped at ground level, footing solid, wood above sound | Rot at the ground line | Concrete repair spur bolted beside the post, or a metal repair spur driven into the old base | When rot runs up the post past where the bolts would go |
| Post leaning, and the concrete lump tilts with it | Shallow or narrow footing, or seasonal ground movement | Straighten and fit a spur in fresh ground beside the old footing, or reset the post deeper | When the new hole is as shallow as the old one |
| Post leaning or wobbling inside a footing that has not moved | Timber has shrunk or rotted inside the concrete | Concrete repair spur | When the timber above ground is also soft |
| Timber post split, soft or snapped above ground | Decay or a split in the post itself | Replace the post | A spur here only bolts onto weak wood |
| Post on a patio or concrete base has come loose | Failed bolt-down fixing | Re-fix the bolt-down with masonry fixings, not overtightened | When the base or the post foot is damaged |
| Concrete post cracked or snapped | Impact or overload | Replace the concrete post | Spurs are made to bolt through timber, not concrete |
How to fix a broken fence post with a concrete spur
A concrete repair spur is a short reinforced concrete post with holes for bolting it to the side of an existing timber post. We stock two sizes: a 3ft spur in a 3″ x 3″ section and a 53″ spur in a 4″ x 4″ section, at £14.34 and £15.54 including VAT at the time of writing. The 3ft concrete spur post suits most domestic fences; the 53″ version is meant for taller or more exposed runs.
- Check for buried services. Find out where drains and cables run before you dig, and ask your neighbour if the post is on a shared line.
- Prop the fence. Leave the panels in place and brace the post upright with timber props while you work.
- Dig beside the old footing. Dig a fresh hole tight against the post, on the side away from the panels if you can. Plan for roughly half the spur’s length below ground. If the old concrete is in the way, break enough of it out to let the spur sit flat against the post.
- Deal with the rotten section. If the stump is rotten, cut it off just above ground and treat the cut end with two liberal brush coats of end grain preservative. Never bury a cross-cut end of treated timber, because the untreated core is exposed.
- Plumb, mark and drill. Get the post vertical in both directions with a spirit level. Hold the spur tight against it, mark through its holes, then drill straight through the post.
- Bolt it. Fix through each hole with M10 coach bolts or carriage bolts, or M10 coach screws, and tighten so the spur and post are pulled together.
- Set the spur. Check the level again, then fill the hole with post mix and leave the props in until it has set. Our guide to how deep fence posts should be covers hole sizes and setting posts in Essex soils.
Worked example: will the spur reach sound timber?
If about half the spur goes in the ground, the other half is all you have for bolting. A 3ft spur is about 914mm long, so roughly 457mm stands above ground. A 53″ spur is about 1,346mm long, leaving roughly 673mm above ground. Push a screwdriver into the post at intervals above the ground. If the wood is soft beyond about 450mm, the 3ft spur’s top bolt will land in rot, so use the 53″ spur or replace the post.
Metal repair spurs and bolt-down supports
Metal repair spurs and stakes are the main alternative. They drive into the ground or into the old stump beside a post that has snapped at ground level, and they rely on a sound concrete base. Stake systems typically use two stakes per post, screwed into the timber with exterior wood screws. They are quick to fit, but they depend entirely on the old footing staying put. If the footing is the problem, a metal spur inherits it.
Bolt-down supports are for posts standing on a hard surface, such as a patio or concrete pad. They are fixed down with masonry fixings, which should not be overtightened.
When to replace the post instead
- The timber is soft, split or crumbling above ground, higher than a spur can reach.
- Several posts along the run are failing at the same time. That points to the whole fence reaching the end of its life, which our repair or replace cost guide looks at in detail.
- The post is concrete and has cracked or snapped. With slotted concrete posts the panels lift out of the slots, so the broken post can be dug out and replaced without rebuilding the bays either side.
Storm season checks for fence posts
The UK storm naming season runs from 1 September to 31 August, and the Met Office’s 2026/27 list starts with Austen, Boelo and Chloe. After any spell of high wind, walk the fence and check each post in this order:
- Push each post at shoulder height. Movement at the top that you can see at the base means the footing or the ground line has failed.
- Look at the soil around each footing for a crescent-shaped gap. That shows the concrete has rocked.
- Check that panels still sit fully in their slots or on their brackets.
- Prop any loose post straight away, before the next gale works the gap wider.
A leaning post caught early is usually a spur job. Left through a winter of wind and wet clay, it often becomes a replacement.
Frequently asked questions
Can you repair a fence post without taking the panels down?
Yes. Prop the panels in position while you fit the spur, and leave the props until the post mix has set.
Can you fix a fence post without digging?
Only with a metal repair spur or stake, and only where the post has broken at ground level and the concrete base is still sound. A concrete spur always needs a hole.
Who is responsible for repairing a fence between neighbours?
It depends on who owns the boundary, which is usually set out in the title documents. Our guide on which side of the fence is yours explains how to check, and why it is worth agreeing any work in writing first.
Need a hand with a broken post?
We supply concrete spur posts, timber and concrete posts and post mix from our yard in Weeley, just outside Clacton, and we repair broken posts and replace damaged panels across the area. Call 01255 830820 or ask for a free quote online.

