Key Takeaways
- Standard Fence Post Depth: Bury posts 600mm (2ft) deep in a 300mm wide hole for a standard 1.8m (6ft) fence.
- Essex Soil Adjustments: Increase burial depth to 700mm–750mm in London Clay (to resist shrink-swell seasonal movement) and loose coastal sand/gravel (for lateral grip).
- Correct Post Length with Gravel Boards: An 8ft post is too short for a 6ft panel with a gravel board. Always use a 9ft (2.74m) post when installing 6″ or 12″ gravel boards under a 6ft panel.
- Gate and Corner Posts: Set gate, corner, and end posts 150mm to 200mm deeper than intermediate posts to withstand extra leverage and load.
- Hole Width and Drainage: Dig holes roughly three times the post width and place 50mm of pea shingle at the bottom to allow water drainage.
Almost every fence that blows down failed at the same place
When a fence comes down in a winter storm, people tend to blame the panels. In our experience it is almost never the panels. It is the posts, and it is nearly always because they were not deep enough, or the hole was not wide enough, or the ground they went into was never assessed properly in the first place.
A 6ft closeboard fence is, in wind terms, a solid sail roughly 1.8 metres tall and 1.8 metres wide per bay. Every bit of that force ends up trying to lever the posts out of the ground. Depth is what stops it.
This guide covers the numbers you need, why the popular “one third” rule causes so much confusion, and how the ground under Essex gardens changes the answer. We supply fencing across Clacton, Colchester and the wider county from our yard in Weeley, so the ground conditions below are ones we deal with week in, week out.
The short answer
For a standard 1.8m (6ft) domestic fence in reasonable ground, set your posts 600mm (2ft) into the ground, in a hole roughly 300mm wide, backfilled with concrete or postmix.
Scale it from there:
| Fence height above ground | Minimum burial depth | Hole width (100mm post) |
|---|---|---|
| 1.2m (4ft) | 450mm | 250mm |
| 1.5m (5ft) | 500mm | 300mm |
| 1.8m (6ft) | 600mm | 300mm |
| 2.0m (6ft 6in) | 700mm | 300mm |
| 2.4m (8ft) | 900mm | 350mm |
Gate posts, corner posts and end posts take considerably more load than intermediate posts. Set those 150mm to 200mm deeper than the rest of the run, and use a heavier section post if you can.
The “one third rule” is where people go wrong
You will see the one third rule quoted everywhere, and it is genuinely useful. The problem is that it gets stated two completely different ways, and the two versions give very different answers.
- Version A: bury one third of the above ground fence height. A 1.8m fence needs 600mm buried, so you need a 2.4m post.
- Version B: bury one third of the total post length. A 2.4m post needs 800mm buried, leaving only 1.6m above ground.
Both are printed as gospel on different websites. They cannot both be right for the same fence. Version A is the one that matches standard UK practice and standard post lengths, and it is the one we work to. If you have read Version B and come away thinking your 8ft post should go 800mm into the ground, you will end up with a fence that is noticeably shorter than you planned.
Our advice is to stop thinking about ratios and work backwards from what you actually want:
Post length = burial depth + gravel board height above ground + panel height + a little to spare
The gravel board problem nobody mentions
Here is where a lot of jobs quietly go wrong, and it is worth reading carefully if you are buying materials yourself.
The standard advice is “use an 8ft post for a 6ft fence”. An 8ft post is 2.44m. Bury 600mm and you have 1.84m above ground. A 6ft panel is 1.83m. So an 8ft post buried properly gives you room for the panel and essentially nothing else.
Add a gravel board and the maths stops working:
- 6ft panel (1830mm) + 6″ gravel board (150mm) + 600mm burial = 2580mm of post needed
- 6ft panel (1830mm) + 12″ gravel board (300mm) + 600mm burial = 2730mm of post needed
An 8ft post is 2440mm. It is short in both cases. A 9ft post is 2740mm, which covers both comfortably.
In practice, plenty of installers get away with an 8ft post by burying part of the gravel board or by reducing the depth to around 450mm to 500mm. On sheltered, well drained ground with a light lap panel, that will often be fine. On an exposed coastal plot with a solid closeboard panel, that shortfall is exactly what you are looking at when the fence is leaning three winters later.
Our recommendation: if you are fitting a gravel board under a 6ft panel, buy the 9ft post. The difference at our yard is £31.20 inc VAT for a 9ft T post against £28.80 for an 8ft. Two pounds forty a post is not the place to save money on a fence you want to last twenty years.
One planning note while you are working out heights. Permitted development generally allows a boundary fence up to 2 metres from ground level, dropping to 1 metre next to a highway, and the gravel board counts towards that total. A 6ft panel on a 6″ board comes to 1.98m and is fine. On a 12″ board it comes to 2.13m and is over the limit if the board sits entirely above ground. Our guide to fence height rules in the UK covers the detail.
Essex ground: why the standard answer is only a starting point
The 600mm figure assumes reasonable, stable ground. Essex has several distinct ground types and they behave very differently once you start digging.
London Clay
This underlies a large part of the county, including much of the Tendring coast. The cliffs at Walton-on-the-Naze and the foreshore at Harwich are textbook London Clay exposures, and it runs inland across a great deal of central and southern Essex too.
London Clay is a shrink-swell clay, and a notably aggressive one. It absorbs water and expands in winter, then dries out, shrinks and cracks in summer. The British Geological Survey rates much of it high to very high for volume change potential, and it is behind a large share of the UK’s subsidence claims. For fencing, that seasonal movement works posts loose over time.
What to do: treat 600mm as the floor, not the target. We would go 700mm to 750mm on clay for a 6ft fence. Widen the hole so the concrete has more mass to resist levering. Put 50mm of pea shingle in the base of the hole so water is not sitting directly against the post. And be aware that a hole dug in August, when the clay is like rock, will not feel the same in February.
Chalky boulder clay in the north
North Essex, up towards the Suffolk border and inland of Colchester, sits largely on a chalky boulder clay plateau, technically the Lowestoft Till, left behind by the Anglian ice sheet. It is stiff, stony and full of flint and chalk fragments.
What to do: this is hard, slow digging and you will want a proper post hole digger or a breaker bar rather than a spade. The upside is that once a post is set, this ground holds it well. Standard 600mm is usually adequate, but expect to spend real effort getting there.
Sand and gravel terraces
Patches of Thames terrace sand and gravel turn up across the county, laid down by the ancestral Thames long before it ran where it does now. Parts of the Tendring coastal strip are notably light and free draining.
Free draining ground is kinder to timber, which is a genuine plus. But loose sand and gravel offers far less lateral grip than clay, and a post set at the minimum depth can work loose surprisingly quickly.
What to do: go deeper, 700mm to 750mm, and go wider. On light ground the concrete mass around the post is doing most of the work, so a bigger concrete plug is worth more than an extra 50mm of depth.
Low-lying and estuary ground
Around the creeks, marsh edges and low-lying land near Jaywick, St Osyth and the estuaries, you are dealing with soft alluvial deposits and a high water table.
What to do: this is the hardest ground to get right and the one we would most strongly recommend concrete posts for. Go deeper again, keep the hole generously wide, and accept that you may need to dig through soft material to reach something that will actually hold.
Made ground on newer estates
New build gardens across Essex are frequently sitting on builder’s fill: rubble, subsoil, whatever came out of the foundations. It looks like ground. It does not behave like ground.
What to do: dig through it until you hit natural material, then measure your 600mm from there. Setting a post in loose fill is setting a post in nothing.
Coastal wind exposure
Separate from soil type, exposure matters enormously. The flat, open plots around Clacton, Holland-on-Sea, Frinton and Walton take considerably more wind loading than a sheltered garden inland of Colchester. If your boundary faces open ground or the sea with nothing in between, add depth regardless of what the soil is doing.
Setting a post properly, step by step
- Check for services first. Cables, water pipes and drainage runs are commonly shallower than you expect, particularly on newer estates. If you are unsure, dig the first spit by hand.
- Measure from finished ground level at each post position. On a sloping garden, every hole is measured from the ground where that post sits, not from the highest point in the run. This is the single most common cause of an uneven fence line.
- Dig the hole roughly three times the post width. For a standard 100mm post, that is about 300mm across. A narrow slot gives the concrete nothing to grip.
- Add 50mm of pea shingle to the base. This lets water drain away from the bottom of the post rather than pooling against it. Worth doing on any ground, essential on clay.
- Set and brace the post. Check it for plumb in both directions and brace it. Concrete does not forgive a post that drifted while it set.
- Fill with concrete or postmix. Aim for at least 75mm of concrete all round the post. Postmix is quicker and easier for small runs. For a long boundary, mixed concrete works out cheaper by volume. We stock aggregates, cement and postmix alongside the fencing.
- Dome the top of the concrete and slope it away from the post. A flat or dished top holds a puddle against the timber, which is precisely what you are trying to avoid.
- Let it cure before loading. Postmix sets in minutes but give it longer before hanging panels. Wet mixed concrete wants at least 24 hours.
Which post length do I need?
Using a 600mm burial depth as the baseline:
| What you are building | Height above ground | Post length |
|---|---|---|
| 4ft panel, no gravel board | 1.22m | 6ft (1.83m) |
| 5ft panel, no gravel board | 1.52m | 7ft (2.13m) |
| 6ft panel, no gravel board | 1.83m | 8ft (2.44m) |
| 6ft panel + 6″ gravel board | 1.98m | 9ft (2.74m) |
| 6ft panel + 12″ gravel board | 2.13m | 9ft (2.74m) |
Our concrete T posts run from £27.60 inc VAT for 6ft and 7ft, £28.80 for 8ft and £31.20 for 9ft. You can see the full range of concrete and timber fence posts, and if you are pairing them with gravel boards, our guide to concrete gravel board sizes and prices explains how the two work together.
Whether concrete or timber posts are the right call for your boundary is a separate question, and we have covered it properly in our article on concrete versus wooden fence posts.
Frequently asked questions
How deep should fence posts be for a 6ft fence?
600mm (2ft) as a minimum in reasonable ground. On Essex clay, light sandy ground or an exposed coastal plot, 700mm to 750mm is a better target.
Can fence posts be too deep?
Not from a stability point of view. Extra depth almost always helps. The real limits are practical: digging effort, the length of post you need to buy, the amount of concrete required, and the risk of hitting services. Going deeper than the run needs is wasted money rather than a fault.
How wide should the post hole be?
Roughly three times the width of the post, so around 300mm for a standard 100mm post. On light or loose ground, go wider. The concrete plug around the post is doing much of the work of resisting wind, and mass matters.
Do I need concrete, or will compacted soil do?
For a 6ft fence, use concrete or postmix. Compacted soil or hardcore can be adequate for a low picket or a temporary boundary, but it will not hold a full height panel fence through an Essex winter.
Can I cut a post down to make it fit?
You can, but it usually means the post was the wrong length to begin with, and cutting it will not give you back the depth you have lost. If you are shortening posts to make an 8ft work under a gravel board, buy 9ft posts instead. Cutting a concrete post also exposes the reinforcement, which is not ideal on a post going into wet ground.
How deep should gate posts be?
Deeper than the rest of the run, by at least 150mm to 200mm. A gate applies constant leverage every time it swings, and gate posts are the first thing to go on most fence lines. Use a heavier section post as well if you can.
Fencing materials and advice across Essex
We manufacture and supply fencing from our yard at Westcroft, Rectory Road, Weeley, a few minutes from Clacton-on-Sea, and we have been doing it since 2008. That means most jobs across CO15 and CO16 are a short run for our delivery lorry, and it means you can come and talk to someone who knows what the ground does around here.
If you are planning a fence and are not sure what post length or depth your ground needs, tell us where the job is and what you are building. We will give you a straight answer, and a materials list to go with it.
Browse our fence post range or get in touch for a free quote. Call us on 01255 830820.
This guide is general advice for standard domestic fencing. Ground conditions vary from garden to garden, and boundary walls, retaining structures and commercial fencing may have different requirements. Prices correct at time of publication and subject to change.

